 |
 |
 |
|
XTV0.5G10E-F8 pump from Annovi Reverberi. The XTV0.5G10E-F8 is a 0.5 GPM replacement pressure washer pump for your machine that requires 1000 PSI. This unit spins at 3400 RPM and has a very high temperature rating of up to 140° F, making it ideal for almost any cleaning situation. The unit has a die cast body and a solid brass forged head, as well as very special interior components like, solid ceramic plungers, anodized cooling fans, over sized bearings and aluminum alloy connecting rods, making this pump one that will most likely outlast your pressure washer. Everything about this pump makes it an ideal choice if your current machine needs this specifications. Even the oil usage and change are designed in such a way, that they will require very little down time of your pressure washer. AR Pump recommends that you change the oil after the first 50 hours of running with the AR64516 oil, and then you only need to do this again every 500 hours or there about. Should you already own an XTV0.5G10E-F8 unit and need repair parts or kits, you can click here for its breakdown.
- Manifold: Forged Brass: Strength and no porosity equals long life. Higher hydrostatic pressures, safety, performance.
- Inlet and Discharge Ports: Heavy bosses for added strength.
- Offset Discharge Ports: High efficiency, smooth flow.
- Bolts: Six Bolts, 6mm, grade 12.9.
- Valves:Ultra Form Cages: Durability, strength and long life.
- Poppets, Seat and Spring: 303 and 400 series stainless steel.
- Valve Caps: Machined brass – greater strength.
- Packing and Plungers: High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
- Low Pressure Seals: “U” cup double lip Buna-N. Good positive seal.
- Support Guides: Machined brass one-piece construction to assure proper plunger alignment and to maximize packing and seal life.
- Plungers: Are a special aluminum oxide blend, solid ceramic for long life, strong durability and more resilient.
- Bearings: Oversized for maximum life and load disbursement, two ball bearings on the solid shaft series and a needle bearing on the drive side and ball on the non-drive side for the hollow shaft series. Each bearing is held in position on the crankshaft and crankcase by snap rings. This assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminates the crankshaft from floating.
- Crankcase: Precision die-cast, large cooling fins and anodized (for maximum heat dissipation).
- Rear Cover: Precision die-cast, precision punched gasket sealed and bayonet style sight glass for positive sealing and locking (no threads to loosen).
- Plunger Rods: Stainless steel construction for strength (no plating to scrape off). O-ring plunger sealing system.
- Rod Pins: Precision ground and hardened steel, oversized for load disbursement.
- Connection Rods: One piece special alloy aluminum based and bronze, oversized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
- Crankshaft: Forged one-piece, precision ground and hardened for extremely long life and durability.
- Oil Seals and O-rings: All are constructed of Buna-N rubber. The O-rings have stainless steel garder springs to assure constant tension on the sealing surface.
- Oil Capacity: Flat cover 8 oz. and extended cover 10 oz.
- Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
- Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
- Hot Water: High temperature kits are available to 180º F. Refer to breakdown.
- Wet End Repair: Very simple no special tools are required.
- Mounting Bolt Pattern: Same on the top and bottom of the crankcase for simple drive side change.
- Design: Using advanced fluid handling design programs. Overall pump efficiency is increased.
Items NOT INCLUDED with your pump that you may need: Check out the accessories for this pump on the right hand side of the page! They can help keep your pump running properly!
The PUMP GUARD will 'dump' any water above 145 degrees F. before it reaches your pump (saving you the trouble of rebuilding your pump)
PRESSURE REGULATOR / UNLOADER - if we list one to the right of the pump this is the model we suggest you use with your pump. Other models with different features like adjustable or fixed and with / without chemical injector are available.
The INLET WATER FILTER will catch most small debris before it enters your pump
The EZ-START VALVE will remove the pressure on your motor when you first start your pressure washer, this item eliminates you pulling your trigger on your pressure washer gun when starting your pressure washer
The PRESSURE GAUGE KIT allows you to monitor what pressure you are operating your pump at! This is very important when you are cleaning delicate items like decks, fences and cars! It also helps you diagnose pressure problems with your pump!
PUMP OIL, you can never have enough on hand! Many pumps ship with oil already in them. But you should always have a bottle on hand so you can change your pump oil according to the manufacturers instruction.
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- Max GPM - 0.5
- Max LMP - 1.9
- Max PSI - 1000
- Max Bar - 69
- Power EBHP - 0.4
- Bore Dia. mm - 15
- Stroke mm - 2.2
- Weight Lbs - 8.5
- Max Temp - 140°
- Oil Capacity - 8oz
- Inlet Thread - 1/2”F
- Discharge Thread - 3/8”F
|
|
|
|
|
|
|
|
| Accessories for this product... |
|
|
|
|