 |
 |
 |
|
In high frequency and long time operation, high accurate manufacturing technique is the only answer to the durable reputation Annovi Reverberi XMASS0.5G15E-F33 pumps. The S.S. Series uses include various applications such as reverse osmosis water desalination, seal gland flushing and waste water odor control. S.S. Series XMASS0.5G15E-F33 feature a SAE 316 stainless steel manifold this is totally corrosion-resistance. Special pumps features include our highly concentric bearing positioning on both sides of the crankcase, anticorrosion coated aluminum die cast crankcase, continuously lubricated Viton seals, triple lip loaded oils seals and our ultra thick ceramic plungers that will not crack under extreme variable temperature conditions.
- Max GPM..................0.5
- Max LMP..............................1.9
- Max PSI......................1500
- Max Bar...............................105
- Power EBHP...............0.05
- Bore Dia. mm.........................15
- Stroke mm...................2.2
- Weight Lbs.............................17
- Max Temp...................140°
- Oil Capacity...........................14.5oz
- Inlet Thread ...............1/2F
- Discharge Thread...................3/8F
Items NOT INCLUDED with your pump that you may need: Check out the accessories for this pump on the right hand side of the page! They can help keep your pump running properly!
The PUMP GUARD will 'dump' any water above 145 degrees F. before it reaches your pump (saving you the trouble of rebuilding your pump)
PRESSURE REGULATOR / UNLOADER - if we list one to the right of the pump this is the model we suggest you use with your pump. Other models with different features like adjustable or fixed and with / without chemical injector are available.
The INLET WATER FILTER will catch most small debris before it enters your pump
The EZ-START VALVE will remove the pressure on your motor when you first start your pressure washer, this item eliminates you pulling your trigger on your pressure washer gun when starting your pressure washer
The PRESSURE GAUGE KIT allows you to monitor what pressure you are operating your pump at! This is very important when you are cleaning delicate items like decks, fences and cars! It also helps you diagnose pressure problems with your pump!
PUMP OIL, you can never have enough on hand! Many pumps ship with oil already in them. But you should always have a bottle on hand so you can change your pump oil according to the manufacturers instruction.
|
|
|
 |
|
 |
|
|
|
 |
|
 |
|
Features
- Manifold:
- - 316L - Stainless Steel Block Style: Strength and no porposity = long life.
- - Inlet and Discharge Ports: 1/2 inlet and 3/8 discharge.
- - Offset Discharge Ports: High efficiency, smooth flow
- - Bolts: 8 Bolts, 6mm, stainless steel.
- Valves:
- - Ultra Form Cages: Durable, strength, and long life.
- - Poppets, Seat and Spring: 316 series stainless steel.
- - Valve Caps: Machined 316L.
- Packing and Plungers:
- - High Pressure Packing: V style (D-1) Viton (cotton duct weave base) strong and tightens under load.
- - Low Pressure Seals: U cup double lip Viton, good positive seal.
- - Support and Guides: Machined stainless steel, 2-piece construction and back-up ring to assure proper plunger alignment, maximize packing and seal life.
- - Plungers: Special aluminum oxide blend, solid ceramic long life, strong and durable.
- Bearings: Oversized for maximum life and load dispercement, needle bearing on the drive side and ball on the non-drive side. Each bearing is held in position on the crankshaft and crankcase by snap rings. This assures positive alignment and centering of the connecting rodsand crankshaft in relation to the crankcase, it also eliminates the crankshaft from floating.
- Crankcase: Precision die-cast, large cooling fins and covered with a special anti-corrosion finish.
- Rear Cover: Precision die-cast, O-Ring sealed and bayonet style sight glass for positive sealing and locking (no threads to loosen). This is an AR original. Oil drain plug.
- Plunger Rods: Stainless steel construction for strength, back-up and O-ring plunger sealing system with SST slingers.
- Rod Pins: Precision ground and hardened steel, oversized for load dispersement.
- Connection Rods: 1-piece special allow bronze for higher pressures, oversized for maximum strength, load dispersement, and life. Heavy pin area construction.
- Crankshaft: Forged, precision ground and hardened for extremely long life and durability. Available in 5/8 hollow shafts drive. Shaft key set screws are standard on high-speed version for long shaft life. Mounting flange is 56-C face.
- Oil Seals and O-Rings: All are constructed of Buna-N rubber. The O-rings have stainless steel garder springs to assure constant tension on the sealing surface.
- Oil Drains: Two (2). One in the rear cover and one in the bottom of crankcase
- Oil Capacity: 14 oz.
- Dyno Proven: All pumps are dyno tested to assure the theroretical design meets the actual design.
- Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
- Hot Water: High temperature kits are available to 180°F.
- Wet End Repair: Very simple no special tools are required.
- Two Oil Drain Plugs: Rear cover and crankcase bottom.
- Mounting Flanges: Multiple flanges are available.
- Mounting Bolt Pattern: On top and bottom of the crankcase for shaft reversal.
- Buna-N: Elastomers available.
|
|
|
|
|
|
|
|
| Accessories for this product... |
|
|
|
|