Home > Pressure Pumps > ANNOVI REVERBERI >

XTV3G22D-F7 Annovi Reverberi Pressure Washer Pump
XTV3G22D-F7 Annovi Reverberi  Pressure Washer Pump
Pump: 3/2200 3400RPM


 
XTV3G22D-F7
List Price: $814.44
Our Price: $474.89
SHIPPING: Item Ships in 1 to 7 Days


Availability:: In Stock
Product Code: XTV3G22D-F7
Qty:

Description Technical Specifications Recommended Accessories / Additional Info
 
XTV3G22D-F7 Annovi Reverberi Pressure Washer Pump. This plunger style pump from Annovi Reverberi is one of the strongest made replacement pumps on the market today. The XTV3G22D-F7 pump is constructed with a brass head and sturdy ceramic plungers as well as a body that is die cast from the best materials. All of this lends the pump and your pressure washer to have years of use with little more than general maintenance. The unit is rated for pressure washers which require a 3 GPM at 2200 PSI Flow rate. The valves on the pump are created to be water resistant which provides longevity to the pump as well. Finally the XTV3G22D-F7 has connecting rods made of bronze and or aluminum which help with pressure output. Need parts for your this pump, click here for the parts breakdown of the XTV3G22D-F7 pump.


Features
  • Forged Brass: Strength and no porosity equals long life. Higher hydrostatic pressures, safety, performance.
  • Inlet and Discharge Ports: Heavy bosses for added strength.
  • Offset Discharge Ports: High efficiency, smooth flow.
  • Bolts: Six Bolts, 6mm, grade 12.9.
  • Ultra Form Cages: Durability, strength and long life.
  • Poppets, Seat and Spring: 303 and 400 series stainless steel.
  • Valve Caps: Machined brass – greater strength.
  • High Pressure Packing: “V” style (D-1) Buna-N (cotton duct weave base) strong and tightens under load.
  • Low Pressure Seals: “U” cup double lip Buna-N. Good positive seal.
  • Support Guides: Machined brass one-piece construction to assure proper plunger alignment and to maximize packing and seal life.
  • Plungers: Are a special aluminum oxide blend, solid ceramic for long life, strong durability and more resilient.
  • Bearings: Oversized for maximum life and load disbursement, two ball bearings on the solid shaft series and a needle bearing on the drive side and ball on the non-drive side for the hollow shaft series. Each bearing is held in position on the crankshaft and crankcase by snap rings. This assures positive alignment and centering of the connecting rods and crankshaft in relation to the crankcase, it also eliminates the crankshaft from floating.
  • Crankcase: Precision die-cast, large cooling fins and anodized (for maximum heat dissipation).
  • Rear Cover: Precision die-cast, precision punched gasket sealed and bayonet style sight glass for positive sealing and locking (no threads to loosen).
  • Plunger Rods: Stainless steel construction for strength (no plating to scrape off). O-ring plunger sealing system.
  • Rod Pins: Precision ground and hardened steel, oversized for load disbursement.
  • Connection Rods: One piece special alloy aluminum based and bronze, oversized for maximum strength, load disbursement, and life. Heavy pin area construction, for added load strength.
  • Crankshaft: Forged one-piece, precision ground and hardened for extremely long life and durability.
  • Oil Seals and O-rings: All are constructed of Buna-N rubber. The O-rings have stainless steel garder springs to assure constant tension on the sealing surface.
  • Oil Capacity: Flat cover 8 oz. and extended cover 10 oz.
  • Dyno Proven: All pumps are dyno tested to assure the theoretical design meets the actual design.
  • Valve Design: Each pump series has a valve design that optimizes its highest efficiency.
  • Hot Water: High temperature kits are available to 180º F. Refer to breakdown.
  • Wet End Repair: Very simple no special tools are required.
  • Mounting Bolt Pattern: Same on the top and bottom of the crankcase for simple drive side change.
  • Design: Using advanced fluid handling design programs. Overall pump efficiency is increased.

Accessories for this product...
Pressure Washer Repair Part - BEIG-85.305.001
Our Price: $40.23

Add
5,000 PSI Max Pressure Gauge Kit
Annovi Reverberi Pumps - AR21039
Our Price: $106.06

Add
Annovi Reverberi Pumps - AR21039
1/2" PUMP GUARD - THERMAL RELIEF
Our Price: $8.08

Add
1/2" PUMP GUARD

Share your knowledge of this product with other customers... Be the first to write a review